Mechanical transmission 0A6 car Volkswagen Tiguan 1

Location of markings on the manual transmission
Location on the manual transmission "Strelka 1" and "Strelka 2" Letter designation and date of manufacture of the MKP "Strelka 1" MCP 0A6 "arrow 2" Other data are of a production...

Marking, gear ratios, filling capacities
Marking, applicability of units, gear ratios, filling capacities (front wheel drive car) Manual transmission 6-st. Manual gearbox 0A6, front-wheel drive Letter designation KHL KLX...

Location of markings on the transfer case
Letter designation and part number of the transfer case "arrow" -Arrow A- transfer case part number -Arrow B- letter designation of the transfer case -Arrow C - transfer case QAU....

Clutch pedal assembly
1 - Engine compartment partition with a socket for mounting the support bracket 2 - Seal, must be replaced, between the support bracket and the engine compartment bulkhead, glued...

Removal and installation the support bracket
For better access to the support bracket, move the driver's seat as far back as possible and set the steering wheel to its maximum height position. With the ignition off,...

Removal and installation the clutch pedal servo spring
Move the driver's seat as far back as possible and set the steering wheel to its maximum height. Remove the storage compartment and trim on the driver's side. Carefully cut the...

Removal and installation the clutch master cylinder
Remove the support bracket. Remove the master cylinder rod socket from the clutch pedal by squeezing the locking tabs with T10005 pliers. Place the spacer "A" between the clutch...

Clutch hydraulic drive parts and components
1 - Brake fluid expansion tank 2 - Seal, seals must be installed in the hose 3 - Hose to the tank 4 - Master cylinder 5 - Clamp, when removing and installing the pipeline, pull...

Repair of the clutch release mechanism
1 - Gearbox 2 - Primary shaft lip seal 3 - The working cylinder with the release bearing form a single unit and are replaced only as an assembly, do not wash the bearing, only...

Clutch repair
Instructions: Replace the clutch disc and pressure plate with damaged or loose rivets. Replace the pressure plate and clutch disc only together. Select the pressure plate and...

Gear shift mechanism repair
Mounting position of the gear shift mechanism Arrow A is the direction of gear engagement. Arrow B is the direction of gear selection. A - Gear shift cable B - Gear selection...

Repair of the gear shift lever and gear shift housing
Instructions: Apply grease -G 000 450 02- to the hinge joints and sliding surfaces. 1 - Floor panel, bend the tabs to remove, be sure to replace 2 - Seal, must be replaced 3 -...

Removal and installation drive cables
Instructions: Apply grease -G 000 450 02- to the hinge joints and sliding surfaces. Do not bend the drive cables! 1 - Using a cable tie, tighten the gear engagement cable to the...

Removal the gearbox (front-wheel drive vehicles)
With the ignition off, disconnect the ground wire from the battery. During further work, the engine is suspended using the crossbar -10-222 A- by the lugs. If they are...

Gearbox installation (front-wheel drive vehicles)
Instructions: Replace the self-locking nuts and bolts. Replace the bolts/screws that are tightened by turning them at a certain angle. During the work, it is necessary to...

Checking the oil level in a manual transmission
The gearbox and transfer case have separate oil pans. Remove the noise-insulating casing. Unscrew the threaded oil level check plug "arrow". The oil level is sufficient if the...

Removal the transfer case (vehicles with a turbocharged diesel engine)
Remove the noise-insulating casing under the power unit. Remove the right drive shaft. Mark the relative positions of the elastic coupling of the rear axle drive shaft and the...

Installation of transfer case (cars with diesel engine with turbine)
Remove the plug from the gearbox. Lubricate the differential splines with grease -G 000 100-. Pass the transfer case through the opening "A" of the subframe, without touching the...

Checking the oil level in the transfer case
The transfer case must be in the installation position. Remove the noise-insulating casing. Place a tray under the transfer case. Instructions: Cover the area under the threaded...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian