Brake system of car Volkswagen Tiguan 1

General information about the brake system
Matching the equipment code to the brake type Information about the type of brakes installed on the vehicle, among other things, is contained on the sticker with the vehicle data...

Electrical/electronic components and their installation locations
ABS TRW (ABS/EDS/ASR/ESP) 1 - ABS control unit "J104", installation location: on the hydraulic unit in the engine compartment on the left under the battery. Do not disconnect the...

General instructions regarding the anti-lock braking system
The braking system with which ABS works is designed according to the diagonal scheme. The braking force is increased by means of a vacuum brake booster. Cars with A8S do not have...

Hydraulic unit parts and components
ABS TRW (ABS/EDS/ASR/ESP) 1 - Brake booster 2 - Brake line, master cylinder/pushrod cylinder circuit to hydraulic unit, distinguishing features: diameter 6.5 mm, nipple with long...

Connecting brake pipes from the master cylinder to the hydraulic unit
On the main brake cylinder A - Connects the master brake cylinder pusher circuit and the hydraulic unit, distinctive features: diameter 6.5 mm, nipple with M12x1 thread B -...

Removal the control unit and hydraulic block
Repair kit of plugs 1N0 698 311A 1 - Transport protection (foam) 2- M10 plugs 3 - M12 plugs Installation location. The control unit is screwed to the hydraulic unit and is located...

Removal and installation front axle ABS system components
1 - ABS speed sensor, before installing the speed sensor, clean the hole and apply a little plastic refractory grease G 052112 AZ 2 - Hexagon socket head bolt, 8 Nm 3 - Wheel hub...

Removal and installation of rear axle ABS system components (front wheel drive)
1 - ABS speed sensor, before installing the speed sensor, clean the hole and apply a little plastic refractory grease G 052112 AZ 2 - Hexagon socket head bolt, 8 Nm 3 - Wheel hub...

Removal and installation of rear axle ABS system components (4x4)
1 - ABS speed sensor, before installing the speed sensor, clean the hole and apply a little plastic refractory grease G 052 112 AZ 2 - Hexagon socket head bolt, 8 Nm 3 - Wheel hub...

Removal and installation of ESP system components
Removal and installation of the ESP sensor unit "0419" The lateral acceleration sensor "G200", the yaw rate sensor 43202- and the longitudinal acceleration sensor "G251" are...

Front brake repair, brake caliper FN 3
Instructions: After each replacement of the brake pads, press the brake pedal several times firmly. This is necessary so that the brake pads take their working position. To pump...

Removal and installation front brake pads FN 3
Removal Mark the position of the brake pads if they are still to be used. They must be installed back in the same places, otherwise there will be uneven distribution of braking...

Removal and installation the front brake caliper FN 3
Removal The work is only carried out for replacement or subsequent repair of the brake caliper. Remove the wheels. Use a screwdriver to pry the support spring out of the brake...

CII41 Rear Brake Repair
Instructions: To pump out brake fluid from the reservoir, use the brake filling and bleeding device -VAS 5234- or the bleeding device VA.G 1869/4-. Before removing the brake...

Removal and installation rear brake pads CII41
Removal When removing, mark the brake pads suitable for further use. They must be installed back in the same places, otherwise there will be uneven distribution of braking forces...

Removal and installation the rear brake caliper CII41
Removal Work is carried out only for replacement or subsequent repair of the brake caliper. Instructions: Do not disconnect the connectors of the parking brake actuator motors....

Electromechanical parking brake
1 - Electromechanical parking brake button "E538", installation location: in the center console 2 - Electromechanical parking brake control lamp "K213", installation location: in...

Removal and installation the parking brake electric motor
Removal Instructions: Before disconnecting the connector, turn off the ignition and wait at least 30 seconds. Disconnect connector "1" from the parking brake motor. Unscrew both...

Brake pedal
ATTENTION: Additional mats must not restrict the brake pedal travel. Apply plastic grease G 000 602 to the articulated joints before installing them on the vehicle. 1 - Support...

Repair of brake caliper FN 3
When carrying out repair work, install all parts from the repair kit. Use only alcohol to clean the brakes. Apply a thin layer of mounting paste G 052150 A2 to the walls of the...

Repair of rear brake calipers
When carrying out repair work, install all parts from the repair kit. Use only alcohol to clean the brakes. New brake calipers are filled with brake fluid and air has been bled...

Brake booster/master cylinder parts and assemblies
Instructions: Use only new brake fluid. Take into account the presence of hydrostatic pressure in the brake fluid reservoir! 1 - Pedal assembly 2 - Hexagonal self-locking nut, 25...

Brake booster vacuum pump
With diesel engine Do not disassemble. Vacuum pump "1". Vacuum hose to brake booster "2" with check valve. With a petrol engine Do not disassemble. Vacuum pump "1". Vacuum hose to...

Removal and installation the vacuum sensor G608
Remove the engine cover. Disconnect the vacuum hose together with the vacuum sensor "G608" from the brake booster. Unlock the clamp with pliers "1". Carefully pry and remove the...

Removal and installation the brake light switch F
Disconnect the battery. Remove the air intake hose, air filter housing and battery. Remove the battery bracket. Disconnect the electrical connector "1" from the brake light switch...

Removal and installation the master brake cylinder
Removal Disconnect the battery. Remove the air filter. Remove the battery. Remove the battery bracket. Cover the engine and gearbox with a lint-free cloth. Pump out as much brake...

Removal and installation the brake booster
Removal Disconnect the battery. Remove the air filter. Remove the battery. Remove the battery bracket. Open the wiring box, remove both wire harnesses and put them to one side....

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian