Brake system of car Volkswagen Caddy 3

Technical characteristics of the brake system
Correspondence of the equipment code to the brake devices used Front brakes Engine Equipment code Front brakes 1.4 l. 55 kW (1*) 1ZM FS III (15 inches) 2.0L 51 kW SDI-PD note 1.4...

List of parts and components of the front brake FS III
List of parts and assemblies with notes on installation work for Figure VC7.004: 1. Hexagon head bolt: 10Nm. 2. Brake disc: - ventilated, diameter 280 mm; - thickness 22 mm; -...

Removal and installation brake pads (FS III)
Removal Mark the position of the brake pads if they will be used again. They must be installed back in the same places, otherwise there will be uneven distribution of braking...

Removal and installation the brake caliper (FS III)
Removal Work is carried out only for replacement or subsequent repair of the brake caliper. 1. Remove the wheels. 2. Disconnect the electrical connector of the brake pad wear...

Brake caliper repair (FS III)
When carrying out repair work, install all parts from the repair kit. Use only alcohol to clean brakes. Apply a thin layer of mounting paste G 052 150 A2 to the walls of the brake...

Removal and installation the brake caliper piston (FS III)
Removal 1. Press the piston out of the brake caliper with compressed air. To prevent damage to the piston, install a wooden stop. 2. Remove the sealing ring using the mounting...

List of parts and components of the front brake FN 3
List of parts and assemblies with notes on installation work for Figure VC7.017: 1. Phillips head screw: 4 Nm. 2. Ventilated brake disc: - diameter 288 mm; - thickness 25 mm. -...

Removal and installation brake pads (FN 3)
Removal Mark the position of the brake pads if they will be used again. They must be installed back in the same places, otherwise there will be uneven distribution of braking...

Removal and installation the brake caliper (FN 3)
Removal Work is carried out only for replacement or subsequent repair of the brake caliper. Remove the wheels. Use a screwdriver to pry the support spring out of the brake...

Brake caliper repair (FN 3)
When carrying out repair work, install all parts from the repair kit. Use only alcohol to clean brakes. Apply a thin layer of mounting paste G 052 150 A2 to the walls of the brake...

List of parts and components of the rear brake
List of parts and assemblies with notes on installation work for Figure VC7.023: 1. Speed Sensor (ABS): - before installing the sensor, clean the hole and apply a little plastic...

Removal and installation rear brake pads
Removal When removing, mark the brake pads that are suitable for further use. They must be installed back in the same places, otherwise there will be uneven distribution of...

Removal and installation the rear brake caliper
Removal 1. Remove the wheels. 2. Disconnect the parking brake cable from the lever on the brake caliper. 3. Disconnect the parking brake cable from the bracket on the brake...

Adjusting the parking brake
Adjustment is only necessary after replacing the cables, caliper and brake discs. 1. Remove the ashtray bracket. 2. Press the brake pedal at least three times. 3. Apply and...

Repair of rear brake calipers
List of parts and assemblies of the rear brake caliper with technological notes on repair for figure VC7.031: 1. Brake caliper with parking brake lever: - replace the caliper if a...

Brake booster, brake master cylinder
List of parts and assemblies of the master brake cylinder and brake booster with technological notes on repair for Figure VC7.032: 1. Pedal assembly. 2. Hexagon self-locking nut:...

Brake booster vacuum pump components and assemblies (diesel)
Vacuum pump for 4-cylinder diesel engine with 2 valves per cylinder: 1. Double pump (vacuum pump combined with a fuel pump) 2. Vacuum hose to the brake booster with a check valve...

Brake light switch (F), from 2007
For vehicles prior to the 2007 model year, the brake light switch is located on the brake pedal. Removal 1. Remove the air filter. 2. Disconnect the connector (1) from the brake...

Removal and installation the brake master cylinder
Removal For vehicles with diesel engines 1. Loosen the rear spring clamp of the inlet hose. 2. Unscrew the air filter mounting bolt (arrow). 3. Using an upward movement, release...

Removal and installation the brake booster
Removal 1. Remove the master brake cylinder. 2. Disconnect the vacuum hose from the brake booster. Cars with manual transmission 3. Unscrew the drive cables (1), support (2) and...

Exchange Rate Stability System ESP
A modern car uses a modern system to ensure vehicle stability in various situations that arise while driving. This system is called the Electronic Stability Program and is...

List of components of the ABS Mark 70 (ABS/ASR) system
List of components of the ABS Mark 70 (ABS/ASR) system for figure VC7.044: 1. ABS control unit (J104): - installation location: on the right side of the engine compartment on the...

List of ABS Mark 60 (ABS/EDS/ASR/ESP) system components
List of ABS Mark 60 system components (ABS/EDS/ASR/ESP) to figure VC7.045: 1. ABS control unit (J104): - installation location: on the right side of the engine compartment on the...

Indication of faults using indicator lamps
Pos. Name 1 Anti-skid system warning light (K86) ESP and ASR control lamp (K155) 2 Brake pad thickness indicator lamp (K32) 3 ABS warning light (K47) 4 Brake system warning lamp...

List of parts and components of the master brake cylinder
List of parts and assemblies with notes on installation work for Figure VC7.047: 1. ABS control unit. 2. ABS hydraulic unit. 3. Brake line from master brake cylinder to hydraulic...

Installation of ABS system components
Installation of front axle ABS system components 1. Speed sensor (ABS) 2. Hexagon socket head bolt, 8 Nm 3. Bearing unit 4. Drive shaft Installation of rear axle ABS system...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Caddy 3 Beetle LT 2D LT 28