NOTE: Valid for vehicles: with Premium instrument panel.
The color display in the instrument cluster shows constant readings, menu functions and messages.
The display is divided into several zones (pic. 1.32).
The left zone 1 shows the current ride height setting.
When a fault occurs, the corresponding icon first appears in the middle of display 2 and then at the top.
Messages appear in the middle zone 3 (the figure shows a warning message that the hood, rear door and front doors are open). In addition, menus are displayed that allow you to obtain information and make various settings.
The right zone 4 shows the selected settings or stages of the automatic transmission. The selector position appears in the display field against a light background.
Below 5 are permanent readings. The time is shown in the middle, the daily trip meter on the left and the total mileage of the car on the right (odometer).
Constant readings
The color display constantly shows the outside temperature, the time and the trip odometer.
Daily trip counter
Shows the vehicle mileage since the last reset. The last digit indicates 100-meter segments. Daily counter readings are reset by pressing button A (pic. 1.33).
The daily counter is automatically set to zero when the reading reaches 2000 km.
Odometer
Odometer (trip counter) shows the total mileage of the vehicle.
Outside temperature display
Measurement range - from -40°С to +50°С. When the outside temperature is between +4°C and -40°C, additionally appears in the display field for the outside temperature display: «snowflake pictogram» (warning about the possibility of ice). This icon flashes for the first five seconds and then stays on until the outside temperature exceeds +4°C.
NOTE: When the vehicle is stationary and at very low speeds, the displayed temperature may be slightly higher than the true temperature due to engine heat radiation.
Using the menu via the controls on the wiper stalk
As an example, the menu for entering a warning about the maximum allowable speed is selected. This can happen when, for example, the vehicle is fitted with winter tires that do not match the vehicle's maximum speed.
Mode selection «KOMFORT SETUP»
Hold down key 1 or 2 (pic. 1.34) until the main menu appears «KOMFORT SETUP».
Menu call «Geschwindigkeitswamung»
Turn wheel 3 until you select a menu item «GESCHW. WARN».
Press the wheel to bring up the menu.
Setting a speed warning
Turn wheel 3 until you have selected the speed to be set.
Press the wheel.
Turn the wheel until the nearest value appears. Press the wheel.
Enabling and disabling speed warning
Turn wheel 3 until you select a menu item «EIN/AUS».
Press the wheel. The check mark will indicate whether the speed warning is enabled or disabled.
Exiting the menu «Geschwindigkeitswamung»
To return to the menu «KOMFORT SETUP» press keys 1 or 2.
All other display menus can be operated in the same way.
Main window
When the CD receiver is off, the current time appears in the middle of the display; when the CD receiver is on, the radio station being received is shown. You can select radio stations by turning the wheel (search mode).
You can also change titles by turning the wheel while listening to CDs.
Main menu «Leading to the goal»
This menu can only be accessed when the navigation system is on.
When route guidance is active, route guidance is displayed. If route guidance is not active, the direction of travel and the names of the streets to be traveled are shown.
Main menu «Telephone»
This menu is only available on vehicles with a built-in telephone.
Incoming calls are shown on the display (pic. 1.36) and you can press the wheel to accept or reject the call.
The contents of the phonebook are shown (pic. 1.37) when the phone button on the steering wheel is first pressed and then the wheel is turned. To establish a connection, press the wheel.
Main menu «Multifunctional pointer MFA»
Multifunction pointer (MFA) gives various data on the trip.
To select a drive:
- press the wheel;
- turn the wheel to select a drive;
- press the wheel to retrieve data from the selected drive.
To reset values:
- select the drive you want to clean.
- hold down the wheel for at least two seconds.
By turning the wheel you can call up various indications of the multifunction pointer (MFA):
In storage «Current trip data»:
- travel time;
- distance;
- average speed of movement;
- average fuel consumption;
- instantaneous fuel consumption.
This data is automatically erased from the drive if the ignition has been turned off for more than two hours.
In storage «Data from recent trips»:
- travel time;
- distance;
- average speed of movement;
- average fuel consumption;
- instantaneous fuel consumption.
In storage «After the last refueling»:
- distance;
- average speed of movement;
- average fuel consumption;
- fuel reserve.
The previous readings are automatically erased when refueling.
Main menu «Comfort»
In this menu, you can make various settings for driving comfort.
«arrival home» - here you can set how long the lighting will be on in the mode «arrival home».
«Daylight» - switching on and off daylight.
«Foot area lighting» - the brightness of the illumination of the area where the legs are located when moving.
«speed warning» - in this mode, it is set whether it is necessary to inform about the maximum permissible speed of movement by means of a text and sound warning and at what speed to do this. Use this function, for example, when the vehicle is fitted with winter tires with a maximum permissible speed that is less than the vehicle's maximum speed.
«Time» - In this mode, you can set the current time and choose between 12- and 24-hour readings.
You enter this menu directly when you press the time setting button on the instrument panel.
«Security» - in this case it is set whether monitoring of the interior of the vehicle and protection against loading onto a recovery vehicle should be activated when the vehicle is locked (tilt sensor).
«Opening doors» - set which doors are unlocked.
«doors» - when the radio key unlock button is pressed, either only the driver's door, or only the two left doors, or all doors are unlocked.
«Signals» - whether it should be accompanied by flashing direction indicators. Depending on the vehicle version, the door unlock sound can also be switched on or off.
«Backdoor» - when the radio key unlock button is pressed, will the rear door be unlocked.
«Auto-lock» - whether there will be automatic blocking of all doors when the car is moving.
«Auto unlock» - automatic unlocking of doors.
«Mirrors» - turning on and off the synchronous adjustment of the position of the mirrors.
«Language» - the language for the instrument panel can be set here.
«Units» - sets the units for temperature, fuel consumption and pressure.
«Factory settings» - By selecting this function, you can return to the original factory settings.
Visitor comments